Documents: Go to download!
Table of contents
User manual IceMaker
Before first use, be sure to remove all interior and exterior packaging, and follow the steps under CLEANING & MAINTENANCE to properly clean your unit.
ON/OFF = powers the ice maker on or off
POWER = illuminates to indicate when ice maker is on
ADD WATER = illuminates to indicate when time to add water to Water Reservoir
ICE FULL = illuminates to indicate when Ice Basket is full
SELECT = press to select size of ice cubes or to place unit in cleaning mode
S = Small ice cube indicator light
L = Large ice cube indicator light
CLEAN = illuminates to indicate when ice maker is in cleaning mode
1. Follow the steps under CLEANING & MAINTENANCE before using this unit.
2. Place the unit on a flat, level surface in a location that is protected from direct sunlight and other sources of heat (i.e. stove, furnace, radiator). Ensure there is at least four inches of empty space on all sides of the unit.
3. Allow one hour for the refrigerant fluid to settle before plugging the cord into an electrical outlet for the first time.
1. Ensure the Water Drain Plug is inserted into the drain area.
2. Open the Clear Lid to remove the Ice Basket and pour water into the Water Resevoir. Keep the water level below the MAX level mark. If water levels exceed the MAX level mark, drain any excess water by removing the Water Drain Plug.
3. Replace the Ice Basket and close the Clear Lid.
4. Press the ON/OFF button on the LED Control Panel to begin the ice-making cycle. NOTE: The unit will automatically begin making ice after 20 minutes if user does not restart the unit after filling with water.
5. Select the desired size of the ice cubes by pressing the SELECT button (S = small, L = large). If the room temperature is lower than 60°F (16°C), it is recommended to select the small-sized ice cubes in order to keep ice from sticking together.
6. Each ice-making cycle lasts 7 to 15 minutes, depending on the size of the ice cube selected and the ambient temperature of the room. In extremely hot temperatures, ice-making time may vary considerably.
7. While the ice maker is on, check the water level periodically. If the water pump is unable to pump water, the unit will stop automatically and the Add Water light will illuminate.
8. When the water level is low, press the ON/OFF button to turn the unit OFF, fill water up to the MAX level mark and press the ON/OFF button again to turn ON the unit again. NOTE: The unit will automatically begin making ice after 20 minutes if user does not restart the unit after filling with water.
9. The unit automatically stops working when the Ice Basket is full and the ICE FULL light will illuminate.
10. To ensure a reasonable hygiene level, change the water in the Water Reservoir every 24 hours. When the unit isn’t in use, drain all water left in the Water Reservoir. If the unit requires a deeper cleaning, refer to the CLEANING & MAINTENANCE section for step-by-step instructions.
IMPORTANT NOTE: In the event that the power is disconnected during the ice making cycle or that the LED lights on the Control Panel are blinking, press the ON/OFF button to stop the ice making cycle. Unplug the unit from the electrical outlet. Allow the unit to sit for a few minutes to let it warm up and allow ice to fall from the evaporator fingers. Empty the Water Tray and wait three minutes before restarting the unit.
DO NOT touch the Evaporator while the unit is in use or during the ice making process. This could cause severe burns.
ADD WATER INDICATOR
If the Add Water Indicator comes on, try the following:
• Turn off the unit, add water, and press the POWER button again to restart the unit.
• There may be too much ice. Turn off the Ice Maker, remove some ice from the Ice Basket.
ICE CUBES STICK TOGETHER
• The ice cycle may be too long. Stop the Ice Maker, then restart it when the ice cubes melt. Select the smaller sized ice cubes using the SELECT button.
• The water temperature in the Water Resevoir may be too low. Change the water in the Water Resevoir. The room temperature should be set between 45˚ F - 90˚ F.
ICE MAKER NOT WORKING
If the ice-making cycle seems to be running properly, but no ice is being made, try the following:
• The ambient temperature or water temperature in Water Resevoir may be too high. The unit must be in an environment below 90˚ F. Try pouring colder water (between 45˚ F - 90˚ F) into the Water Resevoir.
• If changing the water or allowing the unit to cool does not work, there may be a leakage of the refrigerant fluid, or a pipe in the cooling system may be blocked. Please take your ice maker to a qualified technician for repair.
LED LIGHTS
• If the LED lights on the Control Panel are blinking, there may be a disruption in the power source. Press the POWER button to stop the ice-making cycle. Let the ice maker sit for several minutes to let it warm up and allow ice to fall from the evaporator fingers. Empty the Water Tray and wait three minutes before restarting the unit.
Your AUTOMATIC ICE MAKER should be cleaned before storing. Following these steps will help to maintain the unit and add to longevity.
1. Remove the Ice Basket, then drain any leftover water by unplugging the Water Drain Plug on the bottom of the unit. Replace the Water Drain Plug.
2. Prepare your cleaning solution. Common cleaning solutions:
• Vinegar and water (ratio of 1:1)
• Lemon and water (ratio of 1:1)
• Bleach and water (ratio of 1 tsp. bleach : 2 qts. water)
• Commercial ice maker descaling and cleaning solution
3. Make sure unit is plugged in and the POWER indicator light is not illuminated. Add cleaning solution to the Water Reservoir.
4. Press the SELECT button until the CLEAN indicator light is illuminated. Then press the ON/OFF button to start the cleaning cycles. The unit will automatically cycle the cleaning solution 5 times.
5. When the cleaning cycles have completed, drain the interior water by unplugging the Water Drain Plug on the bottom of the unit. Replace the Water Drain Plug.
6. Clean the remainder of the interior and the exterior of the unit using warm, soapy water and a non-abrasive towel.
7. Drain the interior of any remaining water by unplugging the Water Drain Plug on the bottom of the unit. Replace the Water Drain Plug.
8. Fill the Water Reservoir with fresh water.
9. Press the SELECT button until the CLEAN indicator light is illuminated. Then press the ON/OFF button to start the cleaning cycles. The unit will automatically cycle the fresh water 5 times.
10. Drain the interior of any remaining water by unplugging the Water Drain Plug on the bottom of the unit, then dry with a non-abrasive towel. Replace the Water Drain Plug.
11. Before storing, keep the Clear Lid open and allow unit to dry completely for 24 hours.
Your AUTOMATIC ICE MAKER can be used to instantly make ice cubes to be for a variety of beverages. Here are some delicious beverages that you can make at home.
• 1 part orange juice
• 1/4 oz. grenadine
• 8 large strawberries, halved
• 11/8 cups white sugar
• 2 cups freshly squeezed lemon juice
• 6 oz. ginger beer
• 2 oz. fresh lime juice
• Fresh lime slices
• 4 bags black tea
• 12 oz. fresh blackberries
• 8-12 basil leaves
• Liquid sweetener to taste
Igloo ICEB26HNSS | Pages: 34 | Created on: 2020-06-12 | File type: PDF | Filename: 84933868_iceb26hnsswl.pdf | Size: 802.07 KB | Language: English, French, Spanish
